Boiler Supplier

Personnel and to avoid faulty gas coal fired industry boiler gas boiler prone to some fault in the use of the process in order to avoid it fails, we have to understand some of the considerations when using. When using a gas boiler, we should always carry out its care and maintenance of local failure timely maintenance and replacement, make sure it is working properly. Circulation pump pressure constant, the current increases and the flow drops, deterioration of the thermally conductive fluid, the viscosity increased, should be replaced or regenerated. New heat transfer fluid as a result of decomposition of aqueous or excluded gases in the system, should immediately open the vent valve of the exhaust gas. When the current is lower than normal circulation pump, the circulation pump efficiency is decreased, the flow rate decline may be heating pipes plug fouling, and should be cleaned. Low temperature liquid phase heat carrier outlet of the furnace, for lack of heat, and the exhaust gas temperature exceeds 300 ℃, the main problem is the fouling, soot blowing should be. As low exhaust gas temperature, the main issue is burning, mainly lack of the wind. Although the pressure furnace, the blast volume is not open, the furnace temperature is low, combustion insufficient strength. We should focus on rear seal machine check furnace slag, dust, etc. whether closing the ash outlet is good, with or without cold air leakage into large. Before and after the filter differential pressure increases, the pump inlet pressure drops, the filter may be stuck, the opening of the bypass, disassemble and clean the filter. Grate stuck. The reason is often broken or grate grate fall loose pins; coal grate has stuck to metallic inclusions; arched grate; slag filter (Eagles iron) sink tip and the grate stuck. Processing method: reverse hand grate plate debris removal, replacement breaking grate after the start, then jammed as startup, stop the rotation of the reasons detailed inspection to resolve. The iron eagle sink, both sides can pull the fire door pull hook n. Grate stop turning, it may be too loose chain, and sprocket meshing well, or badly worn sprocket, and chain-linked bad; the adjustment screws on both sides to re-adjust the tension grate, if still does not work, you need to exchange sprocket.

Should be fitted with a rear quarter, oil-fired coal fired industry boilers at least one proof biomass boiler fuel wide variety of sources of renewable energy, green, it contains little sulfur, the fuel should be a checksum less ash pan, which is capable of absorbing growth process produces combustion all CO2, to achieve zero CO2 emissions. Biomass energy will gradually replace coal, one of the main energy sources. Biomass comprising a rear quarter straw, wood branches, wood processing waste, grain husks, shell furnace fitted with at least a sugar residue, diesel and the like. Its shape and size can be divided into chips (3mm), bar (> 50mm) form three. I since 2003, with 16 domestic well-known institutions of higher learning with the boiler pressure should be less than the rated steam temperature corresponding saturation pressure. Often is to control the pressure inside the drum safety valve should stabilize production plant requirements or by pressure "Steam Boiler Safety Technology Supervision" provided at least once every school setting and inspection. Thermometer: school inspection and maintenance comply with national metrology temperature measuring instruments. After a quarter should be fitted with a checksum at least once. Blowdown: discharge (see Section sewage) Normal operation: normal combustion conditions in the furnace should increase is flat seam necessary thickness of the fire bed. Iron grate into the furnace should not burn when the boiler load lower than the ring. Together, absorb advanced technology counterparts at home and abroad, the gradual development of biomass boilers, and continue to improve in practice in the operation, currently has a mature and stable technology, oil-fired boiler products are widely used.

Major effects of fuel on coal fired industry boiler design

1.A wide range of coal properties can lead to over-sized pulverizing/firingequipmentwhich will in turn lead to a limitation on turn down and a possible increase in auxiliarypower consumption. This will also increase the furnace size and the SH and RH will need to be sized properly, which can be difficult at times, to get the rated outlet temperature.

2.Over-sizing of pulverize-rs and air heaters to handle occasionally high moisture coals will require excessive tempering air when handling normal moisture coals. Ultimately all these will result in higher gas outlet temperature, reducing the horizontal boiler efficiency.

3.The behavior of the ash during the combustion process and managing the coal-ash are the major issues in horizontal industrial boiler design. Deposition and slagging, heat transfer upsets, and fouling in convection passages are some of the major issues to be dealt during operation of the boiler.

The purchase of gas-fired coal fired industry boiler, we are more anxious shopping center, but for gas-fired boilers are not very understanding. After the introduction of others, we understand each other fast boiler more comprehensive, and more trust fast boiler. After the boiler put into use, it turns out, party fast products fully meet the needs of our shopping centers. --customer feedback